How To Clean A Ruger Lcr 22 Magnum

Ruger LCR Revolver Disassembly, Lubrication and Cleaning

I am going to testify you step-past-step how to disassemble, lubricate and clean a Ruger LCR (Lightweight Meaty Revolver) Revolver. This procedure works for any revolver, but the Original Gun Oil I use in this commodity is safe to use on firearms that have polymer (plastic) or forest components.

There is more than 1 way to effectively clean a Ruger LCR or any other firearm. This article will show you the style I exercise information technology, and I discover it to be a quick and effective method.

Original Gun Oil is a CLP product, which ways it is a Cleaner, Lubricant and Protectant all in one.

Some gun cleaning solvents tin harm these materials or degrade the finish on your gun. Original Gun Oil is rubber for the Ruger LCR and all other polymer frame firearms including Glock, Springfield XD, Smith & Wesson M&P Shield, etc.

Cleaning and lubrication of a Ruger LCR is piece of cake and straightforward, requiring minimal disassembly. The just disassembly required is the removal of the grip past removing one screw, and then backing out one pin in order to lubricate the internal components.

This tutorial will permit y'all how to quickly and confidently perform this task in less than x minutes.

How often should I clean my Ruger LCR?

The Best do when it comes to cleaning whatever firearm is to exercise and so later every time it is fired. Whenever a gun is fired, carbon remainder starts to accumulate in and on the firearm. Although a small amount of carbon is not a big deal, it can cause issues if it is allowed to build up. It is best to clean and lube the gun after shooting at the range.

It is also advisable to clean the gun regularly if yous acquit it on your person for self defense. Regardless of your carry method, grit and grime tin can build up in your weapon during regular day to 24-hour interval curtained carry.

The pattern of the Ruger LCR is like to many revolvers and is very easy to maintain.

Ruger LCR Cleaning Supplies

Hither are the supplies you will need to complete the disassembly, cleaning and lube of the Ruger LCR and most revolvers. See my article on DIY Gun Cleaning Station. There are lots of different cleaning products, so I will listing the ones I have used for years of trouble free results:

Cotton swabs or lint-free swabs
Hoppes Boresnake or equivalent (this will save you lot time and try)
Real Avid Diameter Dominate (New Style Bore Snake)
Pistol Cleaning Rod and patches (if you lot do non have a Boresnake)
Original Gun Oil (Veteran Endemic. Save 10% with discount lawmaking SAVEWITHDAVE)
Gun cleaning castor (an erstwhile toothbrush with medium or soft bristles will piece of work)
Pocket-sized screwdriver
Micro fiber material or cotton fiber rags

Why Use a Boresnake?

A Boresnake is an ingenious invention that allows y'all to quickly and conveniently clean the inside of any gun barrel (and charging holes in the cylinder for revolvers). This avoids using the messy and fourth dimension-consuming method of cleaning the barrel with a rod and patches. Although extremely effective, the rod and patches procedure is messy and should exist used if your gun is especially muddied, or if it has not been cleaned regularly.

Ruger LCR Cleaning video

Steps to Clean and Lubricate the Ruger LCR

Unload the Ruger LCR — Unload the gun and remove all ammo from the surface area.

Apply a drop or two of Original Gun Oil to each charge hole in the cylinder — Open the cylinder and apply a few drops of Original Gun Oil (or similar Synthetic-Rubber gun cleaning product) into each of the cylinder accuse holes.

Apply a drop of Original Gun Oil into the barrel — Apply a couple drops into the butt.

Run a Boresnake through each charge hole 2-3 times — After waiting a couple minutes for the Gun Oil to penetrate and loosen the dirt, run the bore snake through each charging hole a couple times.

Run a Boresnake through the barrel several times — . Run the Boresnake through the barrel several times.

The barrel and Charging holes should be nice and clean — The barrel and charging holes should be nice and make clean.

Apply a drop of Original Gun Oil to the cylinder pivot — Use a drop or two of Gun Oil to the cylinder hinge and clean with a soft bristle gun brush. And then wipe away all excess cleaning solution.

Press on the ejector rod so it extends as shown. Apply a drop or two of Gun Oil to the ejector rod — Printing on the ejector rod and then information technology extends as shown. Apply a drop or two of Gun Oil to the ejector rod.

Clean around ejector rod with a soft bristle gun brush. Then wipe away all excess cleaning solution. — Clean around ejector rod with a soft bristle gun brush. Then wipe away all backlog cleaning solution.

Apply a drop of oil to the breech face and clean with a soft brush. — Apply a driblet of oil to the breech face and clean with a soft castor.

Wipe all the dirt and cleaner off the breech face.

Lubricating the Ruger LCR

After cleaning as outlined above, be sure to wipe off as much of the cleaner/oil as possible in order to remove all the dirt and crud. At present it is time to lubricate the Ruger LCR.

Utilise only a small-scale amount of oil. The gun does not demand a lot of lube to part. Plus, if y'all cleaned the gun with Original Gun Oil, you need even less. Hither are the lubrication points:

Apply one small drop of oil to the cylinder pivot — Utilize one minor drib of oil to the cylinder pivot. Wipe nigh of it off then only a tiny amount goes into the pivot.

LCR Internal lubrication.

Smith & Wesson recommends lubricating the internal mechanism later on every 1000 "trigger presses". This includes live fire (with real ammo) and dry fire (with dummy rounds or no ammo).

Remove the Grip screw — Remove the grip using a slotted screwdriver to remove the screw on the bottom of the grip.

Slide the grip off the LCR frame — Remove the grip past sliding it off the frame.

Locate this pin on the right side of the gun. — Locate this pivot on the right side of the gun.

Using a small punch, gently push the pin in slightly. — Using a modest punch, gently button the pin in **slightly. You practise NOT desire to push it out the other side!**

Push pin just enough to turn the pivot on the left side — Push pin merely enough to turn the pivot on the left side.

Apply a small drop of oil into the pin hole on the right side. — Apply a small driblet of oil into the pin hole on the right side.

Turn the pivot to line up with the slot and press it back in. — Turn the pin to line up with the slot and press it back in.

Slide the grip back on and put the screw back in snug. — Slide the grip back on and put the screw dorsum in snug, merely not as well tight.

Verify the gun is UNLOADED. Bespeak information technology in a SAFE DIRECTION and press the trigger several times to help spread the drop of oil arond the trigger mechanism inside.

Wipe off any backlog oil on the outside and you lot are done.